Regular Cab SuperCab 4x2 4x4 4x2 4x4 4. If you look inside the wheel wells behind the fender liner, right about where the frame is one O2 sensor, the other is underneath the truck about half way back in relation to the transmission. Install a new O-ring, on the thermostat and position the thermostat in the lower intake manifold. While your engine overheating is an obvious sign of a failing thermostat, boiling and gurgling sounds emanating from your vehicle offer another possible indication. If the valve fails, so does your cooling system and an overheated engine, and driver, often are the unfortunate end result.
Drain the coolant out of the radiator. Normally it is the upstream sensors sensor 1 that go first. The coolant will flow through the engine and absorb the excess heat, cooling the engine down. They see the harshest conditions. The thermostat is designed to open when the engine starts to get hot. Remove the power steering reservoir support bracket. You don't have to let all of it out.
Remove th … em, and pull off the housing, and you will find the thermostat. They are long bolts, but the threads are short. Start the truck and allow it to warm up. Remove the power steering reservoir support bracket. Contrary to what aftermarket coolant manufacturers say, there is no such thing as a universal coolant. Your new thermostat should come with the o-ring gasket, but if it didn't, be sure to buy and install it before you install the new thermostat. Oxygen Sensor There are actually 4 O2 sensors on your truck.
Tighten the bolts to 15-22 ft. The thermostat sits between the engine and the radiator of your Ford F-150. They are available for the following Ford F150 years: 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998, 1997, 1996, 1995, 1994, 1993, 1992, 1991, 1990, 1989, 1988, 1987, 1986, 1985, 19, 18, 17, 16, 15, 14, 13, 12, 11, 10, 09, 08, 07, 06, 05, 04, 03, 02, 01, 00, 99, 98, 97, 96, 95, 94, 93, 92, 91, 90, 89, 88, 87, 86, 85. Drain and recycle the engine coolant. Remove the upper hose on the thermostat housing. Place the thermostat housing on the lower intake manifold and install 2 retaining bolts.
Remove the upper radiator hose at the ther … mostat housing. It is designed to block the flow of coolant to the radiator until the engine has warmed up. Our online parts catalog uses real-time inventory, so you can be assured the parts you buy are in stock at the time of ordering. There is a little half-globe shaped metal housing called the thermostat housing. Once the truck has warmed up, the thermostat will open to release coolant. Fill with pre-mixed coolant until the radiator cannot hold any more.
Step 3 - Remove the upper radiator hose on the thermostat housing Now, you should be able to see the clamp holding the upper radiator hose to the thermostat housing. Heat them up and they will come right off. Start the engine and allow it to reach normal operating temperature while checking for coolant leaks. The sudden failure of an inexpensive part can leave you and your vehicle stranded by the side of the road. Replace it by removing the old thermostat, carefully cleaning off the old gasket. Clean… 2002 Ford F-150 headlight bulb lamp replacement: Purchase the correct replacement headlight bulb s first, before disassembling the vehicle. Just replace it when performing a cooling system service.
Remove 2 thermostat housing retaining bolts and remove the housing. Disconnect the negative battery cable. Step 6 - Put it all back together Now you should put everything back in the opposite order in which you removed it. Your truck can overheat for many different reasons, and it's a problem that should be addressed as soon as possible. Your thermostat reduces engine wear, deposits, and emissions.
Most orders are shipped the same day. Remove 2 thermostat housing retaining bolts and remove the housing. If you have any add ons on your truck, toolbox, lift, larger than stock tires, etc. You could easily be looking below 10-12mpg. Remove the upper radiator hose at the thermostat housing.
Bold, rugged and exceedingly tough, your Ford F-150 makes you feel like the world is at your feet. The thermostat resides in between your engine and your radiator and acts as a temperature controlled engine coolant valve. Within this housing is the thermostat. Remove 2 thermostat housing retaining bolts and remove the housing. Regular Cab SuperCab SuperCrew 4x2 4x4 4x2 4x4 4x2 4x4 4. Disconnect the negative battery cable. Clean the O-ring sealing surfaces.
And frankly, it is, as long as you don't find yourself stuck with an overheated engine. Find out how to replace one before it makes matters worse. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. Sometimes it will take 15 minutes or take a few hours it depends on your luck… It is located on the backside of the intake manifold. The spark plug firing order is 1 - 4 - 2 - 5 - 3 - 6 Follow the top radiator hose from the radiator to the thermostat.